Welcome to the DIY Watch Assembly Instruction

In the next two hours, you will dive into the world of watchmaking.

Please relax, take your time, and enjoy the fun of the craft of watchmaking!

 

Mosel Assembly Instructions

Before starting, you can familiarize yourself with the tools and parts needed:

Tool kit content introduction

Parts:

  1. strap

  2. dial (if you purchased crystal dial, you will have 2 layers included)

  3. stem and crown

  4. movement (Miyota 8N24/82S0/8215/8315)

  5. hands (a pair of spare hands is included)

  6. watch case set (stem & crown, movement holder pre-installed)

* quick release spring bars (optional depending on strap type)


1: Dial and Movement Assembly Installation

1a. Watch Making Hygiene

Watch this tutorial before kick start your Chronograph watchmaking journey. An introduction to proper watch component care and assembly techniques, covering essential tips. Remember to wear your finger cots (2 sizes: Yellow ones bigger & Black ones smaller)

Content:

  • proper watch tools usage

  • proper watch component care

  • assembly techniques with essential tips


1b. Preparing case parts

Your watch case comes pre-assembled in order to keep it clean. This part will show you the individual parts of a case.

Content:

  • How to open case back

  • How to place parts

The following video is for a two-pin case back opener. If you have a three-pin case back opener instead, please scroll pass this video below to access the tutorial for it.


1c. Precaution for movement installation

Mechanical movement is the soul of a watch. It takes great care to install it. In this part, we’ll show you what to be mindful of when you install the movement.

Content:

  • Introduction of different parts of a movement

  • Areas you should not touch

  • Areas you can apply pressure on


1d. Installing stem and crown

Reminders:

  1. 8N24 stem removal button location

  2. 82S0 stem removal button location

Watch assembly and basic watch repair require you to install and remove the stem and crown. You will need to do this multiple times throughout this workshop.

Content:

  • Function of crown

  • How to remove and install crown


1e. Installing dial and movement

If you have our new Mosel Crystal Dial, you will have to assemble the two dial pieces together:

When pressing the crystal towards the dial, please apply pressure only on the ring around the crystal, but not the crystal itself.

Other important notes:

  • Please try your best to keep the crystal (transparent part of the dial) as clean as possible

  • If the dial feet are not straight, you can adjust them slightly using your pair of tweezers; that should make the installation a bit easier.

  • For the alignment, follow the image below. Take note that the crystal is facing down; i.e., the texts on the dial should be flipped.


In this part, we will install the dial, movement holder, and movement. After assembling them, we will proceed to the next part, where we install the watch hands.

Content:

  • Install movement into movement holder

  • Install dial onto the movement

The new movement holder comes with three bulges, that go into three corresponding notches on the movement. This is designed to help aligning the holder with the movement.

If your movement holder does not have these bulges, installation can still be carried out normally.


Before proceeding, please check:

 
  1. Dial and movement holder are properly assembled. The two feet at the back of the dial is correctly installed into the movement.

  2. There can be a gap of less than 1mm between the dial and movement holder. Less is better.

 

2: Hand Installation and Adjustment

If this is your first time installing hands, it might be quite difficult. You can take a break first before continuing.

When you are ready, please select from the following instructions according to the style of your purchased watch kit, two-hand watch (with only hour and minute hand), or three-hand watch (hour, minute, and second hand):


3: Installing Case and Other Parts

【Important】Reminder:

It’s time to check everything on the dial, watch hands, and watch case crystal for dust and smudges. Clean them up with the techniques that was mentioned during 1a. Watch Hygiene video.


3a. Remove stem and crown protective sticker

In this part, we will remove the crown protective sticker

1. This is the blue protective sticker on the crown.

2. Stick some sticky tape (normal one will do) onto the protective sticker. Press on it a few times to make sure it adhere to the tape completely.

3. Tear off the tape. The sticker will come off along with the tape.


The following tutorials differ depending on which version of movement holder you have:

To distinguish between them, check the 9 o’clock spot on the holder:

  • If there is a small bulge at 9, it is the old version.

  • If there isn’t a bulge at 9, it is the new version.

Please select the movement holder you have below:

3b. Points of notice during casing

There are a few important pointers you need to keep in mind during casing. They will help you avoid problems that are hard to fix.

Content:

  • Do not touch the movement

  • Align 9 before 3

  • Keep as level as possible

Warning: Do not force the movement assembly into the case if it appears stuck. The dial can be caught by the inner bezel and be very difficult to remove.


3c. Installing watch case (with old holder)

In this part, we will install the movement assembly with hands into the case

Content:

  • Installing assembly

  • Aligning movement and stem

  • Case removal instruction

  • Installing case back

  • Final check

3b. Installing watch case (with new holder)

In this part, we will install the movement assembly with hands into the case

Content:

  • Installing assembly

  • Aligning movement and stem

  • Case removal instruction

  • Installing case back

  • Final check

3d. (optional) Installing custom rotor

If you have customised a rotor, replace the Miyota rotor with your custom rotor.

Content:

  • Finding the right screwdriver

  • Removing the rotor 

  • Putting on the new rotor


If you need to reinstall, you can refer to this:


Final Check

 
  1. Try winding and setting time, see if the watch functions properly. When hands are turned, check if they come into contact with other hands or parts.

  2. Check for dust or dirt on crystal, hands, dial or other parts. If needed, you can remove the case to clean the inside.

  3. Check if the case back is securely fastened. If not, water resistance capability of the watch might be compromised.

 

Almost there!

Good job! You are now one step away from your DIY watch!